DG Creations
With a Mesh Track


All Wheels are Custom Made!  

We do not stock any wheels, every wheel is custom made upon receipt of the order.  We will make every effort to ship right away, but please be aware they may not ship for up to 14 business days.  You are free to contact us prior to ordering to check on current shipping times.  Showing "IN STOCK" means that we have the lid color of your choosing and are able to process the order.

You will receive a cage lock when choosing/purchasing a floor stand for your wheel to help keep it from moving around.

If you are purchasing a Cage Wheel with a removable bearing assembly and will be purchasing a Travel wheel now (or later), we do sell the wheel head only!  This is listed as our Replacement Wheel Only.   You can then remove the bearing assembly from the large wheel and put it on the travel wheel you have stored in your Carry-All with your travel cage!  Our wheels are made to fit any of our stands with no alterations or additional parts needed.



The wheel MUST sit on TOP of the PVC pipe (all stands).  If it's a side mount, there is a small piece of pipe glued into the fitting, a floor stand has the upright pole.  If these are not mounted properly, your wheel WILL FALL OFF.  


Click image to order! 

The unique design of our Wheel comes complete with . . .

Your choice of Bearing Systems:

  • A Removable Bearing System.  This system allows you to detach the wheel to wash without getting the bearings wet. 
    • DESIGN CHANGE DECEMBER 2011 - We are now placing a cap over the end where the bolt head is showing and using a wrench to tighten the wheel onto the tee (which houses the bearing assembly).  This change was make to enable the purchaser greater ease when assembling the wheel and no worries over the possibility of the "nail" bending because you tightened it too much.  Overtightening is no longer a problem!
  • A Permanently Mounted Bearing System.  We have customers with no interest in removing the assembly and they've ask us to offer a permanent feature where they don't need to do anything at all!

Size:  The depth of the wheel is the entire wheel, from the front cover to the very back of the assembly.

The Large Wheel stands approximately 19-1/2" tall, 12" wide and 8" deep (9-1/4" with the bearing assembly attached). There is approximately a 7" clearance between wheel and floor.

The Small Wheel stands approximately 14" tall, 9-1/2" wide and 6-3/4" deep. There is approximately a 7" clearance between wheel and floor.

 A continuous one-piece extruded plastic mesh track which allows waste to fall through.

Your Choice of (3) PVC Stands:

  • Floor Stand
  • Side-Mount for Wire Cages:  Choose either a
    • Horizontal or
    • Vertical

Want a PVC Frame Mount for your PVC Framed Cage - Instructions Here


Available in Mix or Match Colors

The large wheel comes in your choice of (10) colors and the small wheel in a choice of (2) colors

           Lids have FDA approval


03/04/13  Turquoise Blue         07/30/13  Lime Green  




Bearing Assembly:  When putting the tee and bearing assembly onto the wheel, please ensure that it has been properly tightened.  The bearing assembly is to be snug and tight.  Failure to do so will result in the wheel coming off the assembly and stand. 

NOTE:  Dec. 2011 - we no longer use a nail, we have been able to locate wrenches that can be used and make it much easier to "tighten" the wheel without any fear of bending the nail.  The wrenches are included with each Wheel with a Removable Bearing Assembly.

Side Mount:  We have no idea what type of cage you own and cannot guarantee it can withstand nor uphold the weight and/or vibration of the wheel (approximately 1-1/2 pounds for the Small wheel and 2 pounds for the Large wheel).  It may be possible that side mounted wheels will break the welds on some smaller wired cages.

Wobble:  Occasionally a wheel will wobble - we try out best to center everything, but any slight deviance (either ours or that of the manufacturer, our suppliers) can make the wheel spin in odd ways.  Some even have a slight bounce to them!


NOTE:  If you would like to have more than the current 7" clearance between the bottom of the wheel and the floor of your cage, you can request a taller pole when placing your order. 


Don't forget to check out the Treadmill and The Tilt-n-Whirl


Our products are hand-crafted, not factory produced.  Although they will be clean and functional, they may not be mass-production perfect.  Wheels, Treadmills and Tilt-n-Whirls are made from bucket lids, which are not designed to be used in this form.  Because the center of the lids are designed to be thinner with all manufacturers, you may notice some wheels lean forward, look warped or spin off-center, this will absolutely NOT impede their performance nor is it considered a defect.

Fast-Track© is a pet friendly, smoke-free home.  Pets are not permitted in the construction or sewing areas, nor on, or in any supplies. If you have pet allergies, please contact me prior to placing an order.

Our wheels and treadmills are now SOLD WORLDWIDE!   Even your glider won't call it . . . . "exercise!"©

Merchant Services

Copyright © 2011-2015 Fast-Track, all rights reserved

 Information contained within this website are protected under US Copyright Law. 

Products and their Names are protected under Trademark Laws and also considered "Intellectual Property"